High-quality A/B grade American Maple MDF panel measuring 300mm x 200mm. Ideal for structural projects requiring a high-quality appearance and finish on both the topside and panelling. Suitable for laser cutting. This MDF panel is veneered on both faces of the sheet: A grade veneer on the front and B grade on the reverse. Please note:As wood is a natural product, there is often a crook or bow to the sheet. The natural twist might be in excess of 10mm (see below - Tolerances and Caution) .A wood veneer is not like an artificial surface such as melamine or a laminate. It is cut from the log and therefore has its own unique grain, texture, and colour. A Grade Veneer is a very high-quality grading (typically the best you will see). The surface of the material will be consistent in appearance with no large variations in colour. Small pin knots are allowed and these would typically be only a few mm in diameter. This grade veneer is on the topside of this MDF sheet. The B Grade Veneer underside shows the natural look of the veneer. There will be changes in colour that show the grain pattern. Sound, smooth knots are allowed and these will typically be under 15mm to 35mm in diameter (depending on the countries grading rules). The surface should normally be free from open knots and plugs. The material should be suitable for paint/stain or a lacquered finish. There are two different cuts that can be used in veneer production: 'Quarter Cut' are cut at 90 degrees, producing the effect of a straight grain.'Crown Cut' are sliced through the log, producing 'Crowns' and adding more character to the finish (as used on this product).This product conforms to E1 (low) formaldehyde levels and is often described as 'Laser Grade' MDF but there is no official classification for this. We believe that E1 conforming MDF is the safest and best MDF for using in a laser cutter. Features:A/B grade American Maple finish.Veneer thickness approximately 0.5mm.High-quality wood and veneer, for great-looking finishes.MDF core.Suitable for use in internal dry conditions as defined in EN 622 parts 1 and 5 and conforms to EN13986.Low formaldehyde emissions.Contents:1 x 4mm American Maple MDF, 300mm x 200mm Sheet.Dimensions: Length: 300mm. Width: 200mm. Height: 4mm. Veneer thickness (approximately): 0.5mm.

High quality 4mm x 600mm x 400mm Birch Plywood sheets. Suitable for a wide range of applications, including use on a laser cutter.   This is BB/BB grade Birch Plywood with B grade on the topside and BB grade on the underside.

High quality A/B grade American Maple MDF panel measuring 600mm x 400mm. Ideal for structural projects requiring a high quality appearance and finish on both the topside and paneling. Suitable for laser cutting.   This MDF panel is veneered on both faces of the sheet: A grade veneer on the front and B grade on the reverse.

Dies ist ein hochwertiges, in Finnland hergestelltes Birkensperrholzblatt der Güteklasse BR 3 mm, das sich für eine Vielzahl von Anwendungen eignet und mit dem Laser geschnitten werden kann. Dies ist Birkensperrholz der Güteklasse BR "Furnier". Es ähnelt dem Material der Güteklasse B und hat Äste, die in der Regel einen Durchmesser von 7 bis 8 mm nicht überschreiten. Es zeigt das natürliche Aussehen des Holzes und weist natürliche Farbabweichungen auf. Diese Sperrhölzer werden für spezielle Anwendungen verwendet und fühlen sich in der Regel etwas hochwertiger an. Die Oberfläche des Materials ist glatter geschliffen als die der meisten Sperrhölzer. Für dieses Sperrholz wird ein Leim der Klasse 1 nach EN 314-2 verwendet, der für den Innenbereich (trocken) geeignet ist. Innenleim wird im Allgemeinen als die bevorzugte Option für Materialien angesehen, die mit dem Laser geschnitten werden sollen. Wir verwenden Innenleim, weil Außenleim ein deutlicheres "verbranntes" Aussehen auf und um die Schnittfläche herum verursachen kann. Dieses Material ist PEFC-zertifiziert. Eigenschaften: Hochwertiges Material mit einer glatteren Oberfläche als typisches Sperrholz. PEFC-zertifiziert (Programme for the Endorsement of Forest Certification). Leim für den Innenbereich. 6-lagiges Sperrholz. Inhalte: 1 x 3mm BR Birke Laser Sperrholz, 600mm x 400mm Blatt. Abmessungen: Länge: 600 mm. Breite: 400 mm. Höhe: 3 mm. Toleranzen:Die Herstellungstoleranz für die Dicke von Sperrholzplatten beträgt die angegebene Dicke +/-10%. Das bedeutet, dass eine 3 mm Sperrholzplatte zwischen 2,7 mm und 3,3 mm dick sein kann.  

High quality A/B grade Black American Walnut Veneered MDF panel measuring 600mm x 400mm. Ideal for structural projects requiring a high quality appearance and finish on both the topside and paneling. Suitable for laser cutting. This MDF panel is veneered on both faces of the sheet: A grade veneer on the front and B grade on the reverse.  

Decoflex is a jointed sheet of veneer measuring 300mm x 200mm that is extremely easy to work with. The jointed veneer sheet is first pressed onto paper. The wood fibres are then broken and finally it is also pre-sanded with a 150 grain. This gives a flexible sheet of high quality wood veneer. The rear face of the veneered sheet is covered in a paper backing that is a similar colour to the chosen wood. These veneered sheets can easily be cut with a knife or laser cutter.

High-quality A/B grade Steamed Beech Veneered MDF panel measuring 600mm x 400mm. Ideal for structural projects requiring a high-quality appearance and finish on both the topside and panelling. Suitable for laser cutting.   This MDF panel is veneered on both faces of the sheet: A grade veneer on the front and B grade on the reverse.

This extruded 3mm Silver Mirrored Acrylic Sheet from Perspex measures 400mm x 300mm. Mirror acrylic sheets are extruded clear sheets with a high quality mirror coating applied to one face. They make an excellent alternative to glass mirrors. Shatter proof, marr-resistant and 17x stronger than glass, they can be used indoors for decoration or outdoors in the garden. As acrylic mirrors are more flexible than glass they must be fixed to a flat wall/surface. If you are fitting it to a wall which is not flat, it is best to fit it first to something rigid such as a piece of MDF. Features: Mirror finish. Shatter proof. Very low light transmission. Easily laser cut, drilled and thermoformed. Applications:Mirror acrylic sheets have many applications such as display, point of sale, artistic and architectural installation, and of course replacement mirrors. Working with acrylic acrylic sheets:Acrylic is a versatile material that can be cut, drilled, laser cut and thermoformed. Note when laser cutting place the rear side of the sheet to the top, so the laser is not bouncing off the reflective surface. Acrylic is a thermoplastic which means that when it is heated above 140-180°C it becomes flexible. This allows the material to be formed into the required shape or bent. Once the material cools below 85°C it becomes rigid again. Acrylic sheets are often shaped using a CNC router or laser cutter. The edge of laser cut acrylic has a pleasing polished look. If you look carefully at the edge of a piece of laser cut acrylic you can often see slight vertical lines that are caused by the pulses a laser uses when cutting. If you want to get a perfectly smooth finish on the edge of piece of machined acrylic a polishing technique can be used. Typical polishing techniques include diamond polishing and flame polishing. It also possible to etch the surface of a acrylic sheet using a laser cutter. This can produce some very pleasing visual effects. The acrylic sheets have a protective film on both faces. If you are etching the material then this should be removed from the surface that is to be etched. If you are just laser cutting then this film can be left in place (if you wish) as it does not create any harmful gases when it is laser cut (unlike PVC). More detailed information and resources on working with acrylic can be found in our resource section. Contents: 1 x Silver Mirrored Acrylic Sheet (Extruded) 3mm x 400mm x 300mm. Perspex colour reference code: Silver. Dimensions: Length: 400mm. Width: 300mm. Thickness: 3mm (nominal). Tolerances:The manufacturing tolerance for the thickness of extruded acrylic sheets are the stated thickness +/-5%. This means a 3mm sheet could be between 2.85mm and 3.15mm in thickness.

3 mm spiegelnde, farbige, extrudierte Acrylplatten aus Plexiglas mit den Maßen 600 mm x 400 mm. Die Oberfläche der Platte ist hochglänzend.   Sie sind bruchsicher, kratzfest und 17-mal stärker als Glas und können im Innenbereich zur Dekoration oder draußen im Garten verwendet werden.

This Bulk Pack of 3mm Opaque Perspex Acrylic Sheets contains nine sheets, each measuring 297mm x 210mm (A4). The surfaces of the sheets have a high gloss finish. You cannot see through opaque Perspex sheets meaning they can be used in designs/products to provide areas of solid colour.

These 2.3mm Grey Laser Compatible Rubber A4 (210mm x 297mm) sheets are highly versatile and are the perfect choice for a rubber that will be cut with a laser. When cut it produces no harmful gasses and it doesn't emit any odours, if you've ever cut rubber on a laser cutter before you'll know that this is a great feature. It can be engraved and cut with any type of CO2 laser and offers outstanding engraving and impression quality. Although it has a number of potential uses, it's high resistance to alcohol and water based inks makes it the ideal choice for making custom rubber stamps. Other possible uses include; Making custom seals, rubber feet, protective strips and even durable external decorations for your projects/designs. Features: No smell when cut on a laser. High reistance to alcohol and water based inks. Very durable. High friction. Easy to cut. Waterproof. Contents: 1 x 2.3mm Grey Laser Compatible Rubber A4 (210mm x 297mm) sheet. Dimensions: Length: 210mm. Width: 297mm. Height: 2.3mm.

Die Acrylglasplatte/Plexiglasplatte ist aus 100% recycliertem Acrylat hergestellt. Die Platte ist farbecht und UV resistent. Ein weiterer grosser Vorteil der Acrylglasplatte ist, dass sie recycliert und wiederverwendet werden kann. Technische Daten Material: Recycliertes Acrylat / Plexiglas Dicke: 3 mm Toleranz Dicke: 0.4mm +/- 10% der Nominaldicke Expansionskoeffizient: 0,6 mm/m/10ºC Brandschutzklasse: E (nach EN13501) Gebrauchtstemperatur: -40ºC to +80ºC Schutzfilm: PE-Schutzfilm auf beiden Seiten Extra: Eco, hergestellt aus 100% recycliertem Acrylat, UV resistent

These high quality and highly versatile 1mm Cork sheets, measuring 600mm x 400mm, are one of the most Eco-friendly raw materials on the planet and they also offer a wide range of Design and Technology/Making applications. This material is suitable for laser cutting and laser engraving and as such, it can be cut into intricate shapes very easily and then laser decorated. Cork has so many things going for it that it is a must for any making environment. Cork is a waterproof material and is also surprisingly durable. It has good elastic and compression properties and excellent thermal, acoustic and anti-vibration resistance, making it suitable for a wide range of uses. As well as the obvious cork boards, some other possible uses include; coasters, mouse mats, heat/sound insulation, to decouple a project from a work surface to inhibit the transference of vibration, as a covering to improve the tactile nature of a product, gaskets, a protective layer or bumper, business card, and the list goes on and on. Cork is considered a slow combustion material in that it will burn if subjected to a persistent ignition source, but it will then burn very slowly and without a flame so it is unlikely to spread. When it does burn, it does so without releasing any toxic fumes. If you wanted to plan a lesson on raw material sustainability then there is NO other material that is better suited to serving as a positive example. The Cork industry is regarded as being very environmentally friendly as the tree that the bark comes from continues to grow and thrive after the bark is removed. Cork is also 100% recyclable, AND, can be used as an alternative to leather. Not only is cork the best material for a 'cork' for bottles, it also has by far the smallest carbon footprint when compared to any other type of bottle stopper material.   Note:As cork is supplied rolled up it will arrive bowed, if using on a laser cutter these sheets should be strapped/taped to the laser bed before cutting. If using magnets to hold the material flat, ensure that they are not in the path of the laser. Features: Cork is highly versatile. It is probably the most sustainable raw material available for making. Cork is water proof. It is suitable for laser cutting and laser engraving. It also has excellent thermal, acoustic, and vibration resistance making it a good insulator. Contents: 1 x 1mm Cork 600mm x 400mm sheet. Dimensions: Length: 600mm. Width: 400mm. Height: 1mm.  

Diese umweltfreundlichen 2,3 mm grünen ECO-Laser-kompatiblen Gummiplatten im Format A4 (210 mm x 297 mm) sind äusserst vielseitig und die perfekte Wahl für Gummi, das mit einem Laser geschnitten werden soll. Beim Schneiden entstehen keine schädlichen Gase und es ist viel geruchsärmer als andere Gummiprodukte. Wenn Sie schon einmal Gummi mit einem Laserschneider geschnitten haben, werden Sie wissen, dass dies eine grossartige Eigenschaft ist. Es kann mit jeder Art von CO2-Laser graviert und geschnitten werden und bietet eine hervorragende Gravur- und Abdruckqualität. Dieser ECO-Gummi ist ein umweltfreundlicher Lasergravur-Gummi, der aus organischen Bestandteilen hergestellt wird. Eine Seite der Platte wurde aufgeraut, damit sie die Tinte besser aufnimmt. Der Gummi hat eine angenehme, leuchtend grüne Farbe und ist bereit für den Laserschneider. Obwohl es eine Reihe von Verwendungsmöglichkeiten gibt, ist es aufgrund seiner hohen Beständigkeit gegenüber Tinten auf Alkohol- und Wasserbasis die ideale Wahl für die Herstellung individueller Gummistempel. Weitere mögliche Verwendungszwecke sind die Herstellung von kundenspezifischen Dichtungen, Gummifüßen, Schutzstreifen und sogar haltbaren externen Dekorationen für Ihre Projekte/Designs. Abmessungen: Länge: 210 mm. Breite: 297 mm. Höhe: 2,3 mm.

Es handelt sich um ein hochwertiges Sperrholzblatt der Güteklasse 3 mm B/BB aus Birke (Laserply) mit den Maßen 600 mm x 400 mm, das für eine Vielzahl von Anwendungen geeignet ist und sich besonders gut zum Laserschneiden eignet. Beide Deckschichten sind mit dekorativen Birkenfurnieren versehen und der Kern besteht aus Pappelsperrholz. Der Pappelkern hat eine geringere Dichte als reines Birkensperrholz, was bedeutet, dass es problemlos mit niedrigeren Leistungseinstellungen gelasert werden kann. Der Pappelkern bedeutet außerdem, dass die Platten leichter sind als Birkensperrholzplatten. Das Deckfurnier der Güteklasse B: Diese Qualität zeigt das natürliche Aussehen des Holzes. Es gibt Farbveränderungen, die das Maserungsbild zeigen. Solide, glatte Äste sind erlaubt, und diese haben in der Regel einen Durchmesser von weniger als 15 mm bis 35 mm (je nach den Sortierregeln des jeweiligen Landes). Die Oberfläche sollte normalerweise frei von offenen Ästen und Zapfen sein. Das Material sollte für eine Lackierung oder Beizung geeignet sein. Rückenfurnier der Güteklasse BB: Diese Güteklasse ähnelt der Güteklasse B, erlaubt jedoch größere Äste und Reparaturen an der Oberfläche. Es sind solide, glatte Äste erlaubt, die in der Regel einen Durchmesser von weniger als 50 mm haben. Offene Äste können mit Holzdübeln repariert werden. Das Material sollte für Anwendungen geeignet sein, bei denen das optische Erscheinungsbild nicht entscheidend ist. Für dieses Sperrholz wird ein Leim der Klasse 1 nach EN 314-2 verwendet, der für den Innenbereich (trocken) geeignet ist. Innenleim wird im Allgemeinen als die bevorzugte Option für Materialien angesehen, die mit dem Laser geschnitten werden sollen. Der Grund dafür ist, dass der Außenleim ein deutlicheres "verbranntes" Aussehen auf und um die Schnittfläche herum verursachen kann. Bei den für diese Platte verwendeten Hölzern handelt es sich um schnell nachwachsendes Kulturholz, was sie zu einem sehr nachhaltigen Produkt macht. Dieses Material ist PEFC- und FSC-zertifiziert.

Decoflex is a jointed sheet of veneer measuring 300mm x 200mm that is extremely easy to work with. The jointed veneer sheet is first pressed onto paper. The wood fibres are then broken and finally it is also pre-sanded with a 150 grain. This gives a flexible sheet of high quality wood veneer which is ready to be finished with any varnish, stain or wax you may choose. The rear face of the veneered sheet is covered in a paper backing that is a similar colour to the chosen wood. These veneered sheets can easily be cut with a knife or laser cutter.

3mm Rose Gold verspiegelt, farbige Acrylplatte misst 600mm x 400mm. Die Oberfläche der Platte hat eine spiegelnde Oberfläche.

Ein zusammengesetztes Paket aus 37 verschiedenen Materialien und Farben, welches von Acrylglas über Gummi zu Holz reicht. Mit diesem Paket kann man verschiedenste Farben und Formen ausprobieren und so jedes Design zum Leben erwecken. Alle Platten haben die Masse 210 x 300 x 3mm (ausser Gummi: 2.3mm). Folgende Platten sind im Paket: Acryl: Rot Orange Gelb Grün Blau Schwarz Grau Weiss Frosted Glass Transparent Rot Klar Gelb Klar Grün Klar Mirror Gold Mirror Silber Metallic Gold Metallic Silber Metallic Lila Metallic Grün Metallic Ice Pearl White Pearl Pink Pearl Ivory (Elfenbein) Stone White Stone Grey Stone Black Galaxy Blue Gummi: Stamp Rubber Holz: Ahorn Bambus Afromosia Sapele Padouk Amerikanische Eiche Braune Eiche geräucherte Eiche MDF

This high quality A grade Ash Veneer Plywood Sheet (laserply) with a Chinese poplar underside and core is ideal for structural projects requiring a high-quality appearance and finish on the topside and panelling. Knots or resin within the material can cause scorch marks when used on a laser cutter. These can usually be removed with fine grade wet and dry sandpaper. Please note: As wood is a natural product, there is often a crook or bow to the sheet. The natural twist might be in excess of 25mm (see below - Tolerances and Caution). This product is most suitable for applications where a high quality outside surface is needed where visual aspects on the underside are not critical. This is a 'Crown Cut' veneer with A grade topside quality. A wood veneer is not like an artificial surface such as melamine or a laminate. It is cut from the log and therefore has it’s own unique grain, texture, and colour. There are two different cuts that can be used in veneer production: 'Quarter Cut' are cut at 90 degrees, producing the effect of a straight grain.'Crown Cut' are sliced through the log, producing 'Crowns'. This adds more character to the overall finish (as used in this product).Features: High quality A grade Ash Veneer laser plywood sheet (laserply). Veneer thickness approximately 0.5mm. Suitable for use in internal dry conditions as defined in EN 622 parts 1 and 5 and conforms to EN13986. CC grade Chinese poplar underside and core. Please Note:Although this is A-grade Ash Veneer on the topside, the underside and core is CC grade Chinese poplar. We have used the product on our laser cutter successfully. Contents: 1 x 3.6mm Ash Veneer Plywood (laserply), 600mm x 300mm Sheet. Dimensions: Length: 600mm. Width: 300mm. Height: 3.6mm. Veneer thickness (approximately): 0.5mm.

Description This is a high quality 1.5mm Oak Veneered Okoume core Plywood sheet (laserply) which is suitable for a wide range of applications and is suitable for laser cutting. Due to it's Okoume core, it is lighter and more flexible than comparable products.  These thinner plywoods are used in specialist applications and tend to have a slightly higher quality feel. The surface of the material is sanded to a smoother finish than that of most plywoods. Okoume peels and slices easily and evenly, and this combines with its good acceptance of glue to give it wide use as veneer and being processed into plywood. Okoume is very soft and has a very low density and when processed into plywood it makes the combined plywood layers more flexible and lightweight. When flexed, Okoume core plywoods will flex without cracking and won't lose shape like a veneer can when flexed. The glue used in the core is Melamine. EN 314 cl. 2 which maintains its integrity in humid conditions and is less influenced by moisture percentage changes. Note: As wood is a natural product there is often a bow or crook to plywood and in some cases a twist. We have measured curvature of as much as a 25mm rise between the flat centre of the plywood and the corner, therefore if using on a laser cutter these sheets should be strapped/taped to the laser bed before cutting. All of our plywoods, bar this one, use EN 314 cl. 1 bonding glue, which is classified as for indoor use. These 1.5mm Oak Veneered Okoume core Plywood sheets use EN 314 cl. 2 bonding glue which makes the plywood more resistant to moisture. Care should be taken when laser cutting as EN 314 cl. 2 is more easily scorched than EN 314 cl. 1.  Features: Oak veneered plywood sheets (laserply) suitable for laser cutting. High-quality material with a smoother surface than typical plywood. Exterior grade glue. More lightweight and flexible than standard plywood.  Contents: 1 x 1.5mm Oak Veneered Okoume laser plywood (laserply) 600mm x 400mm sheet.    

This Bulk Pack of 3mm Fluorescent Perspex Acrylic Sheets contains five sheets, each measuring 297mm x 210mm (A4). The surfaces of the sheets have a high gloss finish. Fluorescent sheets have an edge that appears to 'glow' under ambient light which can be used to create very striking designs. Fluorescent Perspex sheets are also see through, though the view is tinted by the colour of the Perspex.  Applications:Fluorescent Perspex acrylic sheets have many applications such as point of sale, model making, signs, artistic and architectural installation, casings, etc. Working with Perspex acrylic sheets:Perspex is a versatile material that can be cut, drilled, laser cut and thermoformed. Perspex is a thermoplastic which means that when it is heated above 140-180°C it becomes flexible. This allows the material to be formed into the required shape or bent. Once the material cools below 85°C it becomes rigid again. Perspex sheets are often shaped using a CNC router or laser cutter. The edge of laser cut Perspex has a pleasing polished look. If you look carefully at the edge of a piece of laser cut Perspex you can often see slight vertical lines that are caused by the pulses a laser uses when cutting. If you want to get a perfectly smooth finish on the edge of piece of machined Perspex a polishing technique can be used. Typical polishing techniques include diamond polishing and flame polishing. It also possible to etch the surface of a Perspex sheet using a laser cutter. This can produce some very pleasing visual effects. The Perspex sheets have a protective film on both faces. If you are etching the material then this should be removed from the surface that is to be etched. If you are just laser cutting then this film can be left in place (if you wish) as it does not create any harmful gases when it is laser cut (unlike PVC). More detailed information and resources on working with Perspex can be found in our resource section. Contents: 1 x Mars Red Perspex Acrylic Sheet (Flourescent) 3mm x 297mm x 210mm (A4). 1 x Lava Orange Perspex Acrylic Sheet (Fluorescent) 3mm x 297mm x 210mm (A4). 1 x Hellios Yellow Perspex Acrylic Sheet (Fluorescent) 3mm x 297mm x 210mm (A4). 1 x Acid Green Perspex Acrylic Sheet (Fluorescent) 3mm x 297mm x 210mm (A4). 1 x Neptune Blue Perspex Acrylic Sheet (Flourescent) 3mm x 297mm x 210mm (A4). Perspex colour reference code: Red: 4T56. Orange: 3T19. Yellow: 2T51. Green: 6T66. Blue: 7T97. Dimensions: Length: 297mm (nominal). Width: 210mm (nominal). Thickness: 3mm (nominal). Tolerances:The manufacturing tolerance for the thickness of cast Perspex acrylic sheets are the stated thickness +/-10% plus +/- 0.4mm. This means a 3mm Perspex sheet could be between 2.3mm and 3.7mm in thickness.

This is a high quality Italian Poplar Plywood sheet which is suitable for a wide range of applications and is particularly suited to laser cutting. Poplar has a lower density than Birch, meaning that it can be easily laser cut at lower power settings (See comparison image below).   This Poplar Plywood has an AB grading which is typically the best grade of plywood available.