Products from Vernier Science Education

Vernier Science Education

Celebrating its 35th anniversary in 2016, Vernier Software & Technology continues to be a leading innovator of scientific data-collection technology. Focused on science, technology, engineering, and mathematics (STEM), Vernier is dedicated to developing creative ways to teach and learn using hands-on science and math. Vernier creates easy-to-use and affordable science interfaces, sensors, and graphing/analysis software. With world-wide distribution to over 140 countries, Vernier products are used by educators and students from elementary school to college. Vernier’s technology-based solutions enhance STEM education, increase learning, and build students’ critical thinking skills. Vernier’s business culture is grounded in Earth-friendly policies and practices, and the company provides a family-friendly workplace.

Close filters
 
from to
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
 
 
11 From 38
No results were found for the filter!
Spirometer Durchlaufkopf
Spirometer Durchlaufkopf
An extra flow head eliminates the need for equipment downtime while sterilizing your original flow head. The flow head consists of a polycarbonate outer body with a stainless-steel inner mesh.
CHF118.43 *
Spring Set
Spring Set
This accessory kit contains 6 springs that are ideal for physics experiments. The springs are 6 cm long and 0.8 cm in diameter. Three springs have a spring constant of 5 N/m and the other three have a spring constant of 15 N/m.
CHF37.40 *
Turbidity Cuvette Standard
Turbidity Cuvette Standard
Replacement kit of 100 NTU turbidity standard and one empty glass cuvette.
CHF78.00 *
Vernier Energy Sensor Resistor Board
Vernier Energy Sensor Resistor Board
The Vernier Resistor Board has seven 1 W 5% resistors mounted on a circuit board. Test clip holes on either side of the resistors allow for easy connections to clips on wire leads. The Vernier Resistor Board provides an ideal set of load...
Content 1 Piece
CHF35.32 *
Vernier Variable Load
Vernier Variable Load
The Vernier Variable Load is used in conjunction with the Vernier Energy Sensor to provide a range of resistive loads for projects such as wind turbines or solar panels. Students can adjust the potentiometer to provide resistances...
Content 1 Piece
CHF141.28 *
Analog Protoboard Connector
Analog Protoboard Connector
The adapter fits into a standard prototyping board or National Instruments’ ELVIS prototyping board, providing easy access to the sensor lines. Vernier analog sensors require a 5 volt source and in most cases provide a 0 – 5 volt raw...
Content 1 Piece
CHF24.00 *
DIN to BTA Adapter
DIN to BTA Adapter
This adaptor allows you to connect old DIN style sensors to LabPro, Go!Link, CBL 2, and LabQuest. One end has a female 5-pin DIN connector. The other end is a male BTA connector.
Content 1 Piece
CHF29.00 *
Digital Protoboard Connector
Digital Protoboard Connector
This connector makes it easy to wire the signal from a Vernier digital sensor into a non-Vernier interface. The adapter fits into a standard prototyping board or National Instruments’ ELVIS prototyping board, providing easy access to the...
Content 1 Piece
CHF24.00 *
Digital Sensor Cable
Digital Sensor Cable
This cable connects Vernier digital sensors to the digital (DIG) port on a Vernier interface. Compatible Sensors and Accessories Motion Detector (included with sensor) Drop Counter (included with sensor) Go!Motion Note: The Digital...
Content 1 Piece
CHF9.35 *
DIN Sensor to BTA Input Adapter
DIN Sensor to BTA Input Adapter
This adaptor allows you to connect old DIN style sensors to LabPro, Go!Link, CBL 2, and LabQuest. One end has a female 5-pin DIN connector. The other end is a male BTA connector.
Content 1 Piece
CHF10.39 *
Go! Motion to Calculator Cable
Go! Motion to Calculator Cable
This 84″ cable is used to connect a Go!Motion or CBR 2 to the I/O port of a TI graphing calculator. The cable has the small I/O plug on both ends. The cable can also be used to connect a graphing calculator to the I/O port on a LabPro,...
Content 1 Piece
CHF15.58 *
LabPro Analog Cable
LabPro Analog Cable
This cable can be used to connect your homemade analog sensors you make to Vernier interfaces. There is a BTA plug on on end and six bare wires on the other end. The cable is approximately 1.5 m long....
Content 1 Piece
CHF10.39 *
11 From 38
Viewed